Lufft 8511.EAK Operating Manual Download Page 61

Page: 61 / 158

OID (String)

OID (Numeric)

Remarks

Source Sensor
Assignment

tss.tssSystemSetup.sensorSystemReset.0

.1.3.6.1.4.1.1206.4.2.4.1.1.0

read/write. Note: only command
"restart (1)" is supported !

tss.tssSystemSetup.sensorSystemStatus.0

.1.3.6.1.4.1.1206.4.2.4.1.2.0

tss.tssSystemSetup.sensorSystemOccupancyType.0

.1.3.6.1.4.1.1206.4.2.4.1.3.0

fixed value ! (write operation not
supported)

tss.tssSystemSetup.maxSensorZones.0

.1.3.6.1.4.1.1206.4.2.4.1.4.0

fixed value ! (write operation not
supported)

tss.tssSystemSetup.sensorZoneTable.sensorZoneEntry.sensorZoneNumber.x

.1.3.6.1.4.1.1206.4.2.4.1.5.1.1.x

tss.tssSystemSetup.sensorZoneTable.sensorZoneEntry.sensorZoneOptions.x

.1.3.6.1.4.1.1206.4.2.4.1.5.1.2.x

fixed value ! (write operation not
supported)

tss.tssSystemSetup.sensorZoneTable.sensorZoneEntry.sensorZoneOptionsStatus.x

.1.3.6.1.4.1.1206.4.2.4.1.5.1.3.x

tss.tssSystemSetup.sensorZoneTable.sensorZoneEntry.sensorZoneSamplePeriod.x

.1.3.6.1.4.1.1206.4.2.4.1.5.1.4.x

read/write. Restrictions see
chapter

Fehler! Verweisquelle

konnte nicht gefunden werden.

tss.tssSystemSetup.sensorZoneTable.sensorZoneEntry.sensorZoneLabel.x

.1.3.6.1.4.1.1206.4.2.4.1.5.1.5.x

read/write

length: 8…255

tss.tssSystemSetup.clockAvailable.0

.1.3.6.1.4.1.1206.4.2.4.2.1.0

tss.tssControl.maxOutputNumber.0

.1.3.6.1.4.1.1206.4.2.4.2.1.0

tss.tssControl.outputConfigurationTable.outputConfigurationEntry.outputNumber.x

.1.3.6.1.4.1.1206.4.2.4.2.2.1.1.x

tss.tssControl.outputConfigurationTable.outputConfigurationEntry.outputSensorZoneNumber.x

.1.3.6.1.4.1.1206.4.2.4.2.2.1.2.x

fixed value ! (write operation not
supported)

tss.tssControl.outputConfigurationTable.outputConfigurationEntry.outputFailsafeMode.x

.1.3.6.1.4.1.1206.4.2.4.2.2.1.3.x

fixed value ! (write operation not
supported)

tss.tssControl.outputConfigurationTable.outputConfigurationEntry.outputModeStatus.x

.1.3.6.1.4.1.1206.4.2.4.2.2.1.4.x

tss.tssControl.maxOutputGroups.0

.1.3.6.1.4.1.1206.4.2.4.2.3.0

tss.tssControl.outputGroupTable.outputGroupEntry.outputGroupNumber.x

.1.3.6.1.4.1.1206.4.2.4.2.4.1.1.x

tss.tssControl.outputGroupTable.outputGroupEntry.outputGroupOutputState.x

.1.3.6.1.4.1.1206.4.2.4.2.4.1.2.x

fixed value ! (write operation not
supported)

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Brands by name

Popular brands