12
Messages
2
xx
Paper Jam
The printer detects a paper jam. Although the
location of the paper jam appears on the second line
of the display,
you must clear the entire paper path
before continuing your print job.
W
ARNING
:
If paper is jammed in the optional
2500-sheet tray, do not open the tray until you have
checked the jam access door on the right side of the
printer (Door F) for jammed paper. Opening the tray
when paper is jammed in the vertical transport area
may damage your printer and require a service call.
See “Clearing paper jams” on page 41 for detailed
instructions.
After you clear the paper path, press
Go
to clear the
message and continue printing. The printer prints a
new copy of the page that jammed if Jam Recovery
is set to On or Auto.
Leave Staple Job
in Finisher
Clear Staple Job
from Finisher
Clear Job
from Finisher
Note: If you have an optional finisher attached to
your printer, the message
Leave Staple Job in
Finisher
,
Clear Staple Job from Finisher
, or
Clear
Job from Finisher
may
alternate with the
2xx Paper
Jam
message.
34 Wrong Paper
Size in Tray
x
34 Wrong Paper
Size Manual Feed
The printer was expecting to pick a different size
paper from the specified tray than what it now
detects is moving through the paper path.
If the message indicates the problem is in tray 1,
verify that the Tray 1 Size setting in the Paper Menu
matches the size paper loaded in the tray.
If the message indicates the problem is in tray 2 or
tray 3 (or an optional 500-sheet tray 4), check to be
sure the tray’s left paper guide is in the proper
position for the size paper loaded. This message
may occur, for example, if you loaded letter size
paper in a tray where the left paper guide is inserted
in the slot for legal size paper. In addition, make sure
the paper is positioned in the correct orientation in
the tray. See “Loading trays 2 and 3” on page 88 for
detailed paper loading instructions.
Press
Go
to clear the message and continue
printing. The printer does not automatically reprint
the page that prompted the message.
Printer messages (continued)
Message
Action
Summary of Contents for 12L0103
