Kongsberg Flexview Page 36 Reference Manual Download

Page: 36 / 160

922-20207001/1.0

Applying filters

You can apply an averaging, background removal, or an edge enhancement filter to
the sonar view.

Context

These buttons are located on the tool bar.

Procedure

Click one of the filter buttons.

Observe the changes in the sonar view.

Increase or decrease the filter effect.

Click the

Display Widget

icon.

This icon is located in the lower-right corner of the sonar view.

Drag the

Filter

slider to adjust the strength of the filter.

Click the

No Filter

button to turn off all filters.

Related topics

Filters, page 137

Adjusting the TVG (Time Variable Gain) setting

You can adjust the time variable gain for each sonar application in the

TVG Setup

dialog

box.

Context

TVG

(Time Variable Gain) compensates for the loss of acoustic energy due to geometric

spread and absorption.

Procedure

Click

Setup

→

Connect

to start the Sonar Head.

Select the sonar application you wish to configure from the

Sonar applications list

on the top bar.

Tip

Each sonar application has its own TVG profile.

Click the

TVG

button.

Flexview Reference Manual

Summary of Contents for Flexview

































































































































































Search results

Summary of Contents for Flexview

Reviews:

Related manuals for Flexview

Brands by name

Popular brands

Kongsberg Flexview, Reference Manual

Search results

Summary of Contents for Flexview

Reviews:

Related manuals for Flexview

Brands by name

Popular brands