Kongsberg Flexview Reference Manual Download | Manualshive

Page: 146 / 160

background image

144

922-20207001/1.0

Imaging mode — 1200 kHz

•

Horizontal Field of View

: 75°

•

Vertical Beamwidth

: 21°

•

Angular Resolution

: 0.65°

•

Update rate

: up to 40 Hz

Imaging mode — 1400 kHz

•

Horizontal Field of View

: 45°

•

Vertical Beamwidth

: 18°

•

Angular Resolution

: 0.55°

•

Update rate

: up to 40 Hz

VDSL

Firmware version

: 1.5

Part number

: 320-27701000-0150 (Rx controller)

Important

Although VDSL sonar heads are pre-programmed at the factory with the correct
firmware, you may need to upgrade your firmware if you do not have the latest version
for your VDSL Sonar Head. For the best performance, firmware version 1.5 (or later) is
required for applications using a long cable and VDSL telemetry. Note that you only need
to upgrade the Sonar Head receive firmware file (.RXF) and the Sonar Head software file
(.ASW). You do not need to upgrade the Sonar Head transmit firmware file (.TXF).

You can download these files from our website.

•

https://www.km.kongsberg.com/mesotechsoftware

Mechanical specifications

These mechanical specifications summarize the physical properties of the Flexview
system.

Sonar Processor

The Sonar Processor uses a high-quality commercial-off-the-shelf laptop computer
workstation. The weight and dimensions of the model may vary. Contact your
Kongsberg Mesotech representative for information about the current model that is
delivered with your Flexview system.

Flexview Reference Manual

«
...
144
145
146
147
148
...
»

Summary of Contents for Flexview

































































































































































Reviews:

No comments

Related manuals for Flexview

Brand: Eagle Pages: 68

Brand: Marcum Technologies Pages: 16

Brand: DATASONICS Pages: 110

FarSounder-1000

Brand: FarSounder Pages: 56

Brand: FarSounder Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands