Kalkhoff Bosch Cruise User Manual Download Page 248 | Manualshive

Page: 248 / 550

background image

12

VIII User Manual Pedelec Xion

2. Grip the battery with both hands and lift it forwards/

upwards out of its holder. In doing so, hold on tight to
the battery to prevent it from being dropped. Place the
battery down on a suitable surface. This should be dry,
even and non-flammable.

3. You should now remove the key and keep it in a safe

place to prevent it from breaking off or being lost.

4.2 Learning cycle

After fully charging the battery for the first time and
thereafter roughly once every six months, you must run
the battery down until the system switches off. This
procedure (a so-called “learning cycle”) is necessary
so that the battery management recognises the chang-
es in the capacity caused by age and wear and tear,
in other words, the performance level of the battery.
Afterwards, the capacity of the battery is calculated
anew and correctly represented. This also allows the
remaining range display to function with greater preci-
sion. With this procedure, you can prevent a sudden
loss of electrical assistance during an extended trip.

Removing the battery

4.3 Charging operation

Before charging the battery, read the information on
the charger carefully.

1. Take the charger provided out of its packaging and

plug the mains plug into a socket (110 to 230 V, please
observe type plate on the charger). To charge the bat-
tery safely, the charger must be placed on a suitable
surface. This should be dry and non-flammable.

2. Connect the plug of the charger to the battery. When

positioned correctly, the plug is held in the socket by a
magnet.

3. The charging process begins. The LED on the charger

lights up red. The battery is charged in five stages.
When charging of one stage is in progress, the cor-
responding LED flashes. If this stage has been fully
charged, the LED will light up permanently. Now the
next LED will begin to flash. After all five LEDs have
gone out, the battery is fully charged.

4. If the LED on the charger flashes red permanently, a

charging fault has developed. In that case, disconnect
the battery from the charger, then connect it again. The
charger tests the battery and performs readjustments,
if required. If the LED on the charger still flashes, take
the charger and battery to your specialist dealer who
will test the device and replace it, if required.

5. To save power, pull the charger plug out of the socket

once the charging operation is complete.

Charging the battery

«
...
246
247
248
249
250
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: QU-AX Pages: 44

Brand: 3T Pages: 40

Brand: 77designz Pages: 2

Portside Cruiser

Brand: L.L.Bean Pages: 8

Hakkaliigi Disc 700CC

Brand: ibis Pages: 34

Brand: SP CONNECT Pages: 2

Brand: QPlay Pages: 6

Brand: GLOBBER Pages: 20

Brand: GLOBBER Pages: 74

Brand: Reynolds Pages: 14

Brand: E-Bike Pages: 112

Brand: Winther Pages: 2

MY20 TURBO CREO SL

Brand: S-WORKS Pages: 97

Brand: Vetta Pages: 22

MX Comp ETA 2005

Brand: Marzocchi Pages: 30

Brand: b'Twin Pages: 33

311 FL-X Carbon

Brand: SQlab Pages: 76

Brand: X-TREME Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands