Kalkhoff Bosch Cruise User Manual Download | Manualshive

Page: 84 / 550

background image

II User Manual Fast Pedelec

15

Variation in electric assistance

Propulsive power

Speed

increasing pedal

power and

assistance

reducing

assistance

assistance

switched off

Power-assist

mode = 1 : 2

Pedal force

36 km / h

45 km / h

Propulsive power (pedal force +

electric assistance)

Electric assistance

1.0

2

Fast Pedelec 28"

5.2 Distance

The distance you can travel using the power assist with
the battery fully charged depends on several factors:

•

Ambient temperature

If it is colder, you will travel a shorter distance
with the same battery charge.

To maximise the distance you can travel, keep the
battery in a heated room so that it is at room tem-
perature when you fit it on your Pedelec.

Rate of discharge at different temperatures

Discharge curve at normal temperatures

Discharge curve at low temperatures

Discharge capacity at low temperatures

Discharge capacity at normal temperatures

Discharge capacity (Ah) or hours of use

Difference between nor-

mal and low temperature

Rated voltag

e

Minimum voltag

e f

or

batter

y operation

(cutoff voltag

e)

As the battery discharges when the motor is in use,
it generates enough heat to not lose too much of its
power at low ambient temperatures.

•

Selected assist level

If you want to cover a large distance assisted by
the motor, select the lower gears, i.e. the ones that
are easier to pedal. Also select a low assist level.
"ECO" then appears on the control panel.

«
...
82
83
84
85
86
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: DAPU Pages: 4

Brand: NAKTO Pages: 29

Brand: Factor Pages: 15

Brand: Öhlins Pages: 8

Brand: Mad4One Pages: 5

Brand: Youin Pages: 52

KLICKfix 0211DS

Brand: Rixen & Kaul Pages: 2

Brand: UNIPRODO Pages: 17

CONTRO-E C62216M1002

Brand: Cannondale Pages: 12

Brand: BOS Pages: 4

Brand: SPOT Pages: 41

Brand: Storage Options Pages: 8

Brand: Burley Pages: 36

Brand: Burley Pages: 8

Brand: Burley Pages: 32

Brand: Mactronic Pages: 2

302655/20170601SZ187

Brand: APLIC Pages: 72

Brand: APLIC Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands