Kalkhoff Bosch Cruise User Manual Download | Manualshive

Page: 216 / 550

background image

34

VI User Manual | Impulse Ergo Pedelec

10 Cleaning

›

Remove the battery before you clean your
Pedelec.

›

Do not use benzine, thinner, acetone or similar
agents in the cleaning procedures under any
circumstances. Likewise, the use of abrasive
cleaners and aggressive cleaning agents must
also be avoided.

›

Only use commercially available, household
cleaning agents and disinfectants (isopropyl
alcohol) or water. You can obtain suitable clean-
ing agents and additional information from your
specialist cycle shop.

›

We recommend you clean your Pedelec with a
damp cloth, a sponge or a brush.

10.1 Cleaning the battery

Make sure when cleaning that water does not enter the
battery. Although the electrical components are sealed,
it is not advisable to clean the bike by spraying it with a
hose or a high-pressure cleaner. This could damage your
bike.

When wiping down the battery, be careful not to touch and
connect the contacts on the underside. This could cause
the battery to switch off.

10.2 Cleaning the motor

Dirt should be removed from the motor of your Pedelec
regularly, ideally using a dry brush or a damp (not wet)
cloth. Running water such as that from a hose pipe or even
a high-pressure cleaner must not be used for cleaning.

The ingress of water can destroy the motor. Therefore,
ensure that neither fluids nor moisture enter the motor at
any time during cleaning.

10.3 Cleaning the display

The housing of the display may only be cleaned with a
damp (not wet) cloth.

Do not use other chargers. Only charge the battery us-
ing the charger provided, or a charger approved by us.

•

If a charging fault occurs, the LED in the charger
flashes red. In this case, the charging current is too
high.

•

Disconnect the battery from the charger and then
connect it again. If the error message still appears,
the battery and charger must be checked by a spe-
cialist dealer.

If used incorrectly, the device may be damaged or
inflict injuries.

›

Before cleaning the charger, always pull the plug
out of the socket to avoid a short-circuit and/or
physical injury.

›

Only use the charger in dry rooms.

›

Only place the charger in a secure stable position
on a suitable surface.

›

Do not cover the charger or place any objects on
it as otherwise it could overheat and catch fire.

Charging fault

«
...
214
215
216
217
218
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: Magnum Pages: 26

Brand: Topeak Pages: 2

Brand: CD Pages: 27

Brand: Welkin Pages: 22

Brand: SUPERNOVA Pages: 12

Brand: Vetta Pages: 10

E-HYBRID STREET

Brand: Ghost Pages: 96

Brand: Crivit Pages: 15

Brand: Crivit Pages: 48

Brand: VDO Cyclecomputing Pages: 60

Brand: Xiyuan Pages: 12

Brand: DAHON Pages: 12

Brand: YAMEE Pages: 14

Brand: Pacific Pages: 10

Shimano Steps E8000

Brand: Univega Pages: 184

Brand: Street Surfing Pages: 33

Brand: Kris Holm Pages: 2

Brand: IDEAL Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands