Kalkhoff Bosch Cruise User Manual Download | Manualshive

Page: 266 / 550

background image

30

VIII User Manual Pedelec Xion

10 Cleaning

›

Remove the battery before you clean your
Pedelec.

›

Do not use benzine, thinner, acetone or similar
agents in the cleaning procedures under any
circumstances. Likewise, the use of abrasive
cleaners and aggressive cleaning agents must
also be avoided.

›

Only use commercially available, household
cleaning agents and disinfectants (isopropyl
alcohol) or water. You can obtain suitable clean-
ing agents and additional information from your
specialist cycle shop.

›

We recommend you clean your Pedelec with a
damp cloth, a sponge or a brush.

10.1 Cleaning the battery

Make sure when cleaning that water does not enter the
battery. Although the electrical components are sealed,
it is not advisable to clean the bike by spraying it with a
hose or a high-pressure cleaner. This could damage your
bike.

When wiping down the battery, be careful not to touch and
connect the contacts on the underside. This could cause
the battery to switch off.

10.2 Cleaning the motor

Dirt should be removed from the motor of your Pedelec
regularly, ideally using a dry brush or a damp (not wet)
cloth. Running water such as that from a hose pipe or even
a high-pressure cleaner must not be used for cleaning.

The ingress of water can destroy the motor. Therefore,
ensure that neither fluids nor moisture enter the motor at
any time during cleaning.

Do not clean the motor when it is warm, e.g. immediately
after a trip. Wait until it has cooled down. Otherwise, the
motor may be damaged.

9.2 Installing the rear wheel

1. Place the torque support on the left axle side of the

motor (see point 2 in the image below).

2. Then feed the rear wheel past the rear derailleur and

into the dropout on the frame.

3. If your Pedelec has disc brakes, ensure that the brake

disc is placed exactly in the centre between the brake
blocks.

4. Insert the rear wheel in the dropout so that the torque

support fits exactly and the ends of the axle sit entirely
within the dropout.

5. Close the quick-release device

General User Manu-

al, Chapter 18.6.2 “Inserting the rear wheel ”)

6. Connect the cable between the motor and the battery.

7. Attach the plug to the chain stay once more

using the rubber ring.

8. If your Pedelec has rim brakes, engage the brake cable

once more.

For precise details regarding the handling of rim or
disc brakes and quick-release devices, please refer to
the section of the User Manual concerning the tech-
nology featured in the bike.

Placing the torque support

Motormontage - Bremsseite
Motor mounting - side of the brake

ALBER-Komponenten

Komponenten anderer Hersteller

[1] Motor
[2] Drehmomentstütze in der von Ihnen bestellten Variante (Abweichung zur Grafik möglich)

Rahmen des Fahrrads

[3] Unterlagscheibe
[4] Mutter,

[5] Bremsscheibe
[6] Bremsensatz
[7]

Anzugsmoment: 20 Nm

ACHTUNG: Zuerst die Mutter auf der gegenüberliegenden Seite anziehen, danach diese Mutter!

Bitte beachten Sie bei Ihren Arbeiten die Vorgaben und Empfehlungen des jeweiligen Herstellers zur
Montage seiner Komponenten.

ALBER Components

Components of other manufacturers

[1] Motor
[2] Torque receiver in the version ordered (might differ from drawing)

[3] Washer
[4] Nut,

[5] Brake disc
[6] Brake set
[7] Bicycle frame

fastening torque: 20 Nm

Please pay attention to the instructions of each manufacturer for the assembly of the appropriate
components.

ATTENTION: Tighten this nut after the one on the opposite!

5

6

3

4

1

2

7

4

«
...
264
265
266
267
268
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: SmartTrike Pages: 32

Brand: Daymak Pages: 29

Luci Solar Bike Light Set

Brand: MPOWERD Pages: 5

Brand: wayscral Pages: 320

Brand: Cake Pages: 36

Brand: Bosch Pages: 299

Brand: Bosch Pages: 238

Brand: Bosch Pages: 79

ConnectModule BCM3100

Brand: Bosch Pages: 26

Brand: Bosch Pages: 51

Brand: Bosch Pages: 32

Brand: Bosch Pages: 52

Brand: Bosch Pages: 55

eBike ABS BAS100

Brand: Bosch Pages: 93

Brand: Bosch Pages: 10

Brand: Garneau Pages: 1

Brand: HIMO Pages: 20

E-BIKE K8 SE-2780K

Brand: IconBiT Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands