Kalkhoff Bosch Cruise User Manual Download | Manualshive

Page: 163 / 550

background image

14

V User Manual Impulse Pedelec

5 Control panels

When buying your Impulse Pedelec, there are two different
control panels to choose from: with an LED or LCD display.
With the LED display, lit diodes display the information for
you, while more information is displayed with the LCD ele-
ment. In addition, text and digits are shown on the display.

5.1 LED control panel

1a

1b

2

3

4

5

1 Buttons for power assist level

2 On/Off switch

3 Battery charge state indicator

4 Power-assist mode indicator

5 Button for pushing assistance (optional)

The control panel on the handlebar has three or four but-
tons (depending on the model) and two rows of LED indi-
cators. The buttons used to control the level of assistance
are located on the left-hand side of the control panel.

Above and to the right you can see the row of LED indica-
tors that shows which level of assistance has been acti-
vated and the current battery charge state.

Row of LED indicators for charge state and assistance

The “Power” button is located below the LEDs. Press this
button to switch the control panel on and off.

On/Off button

If the model features pushing assistance, the switch for
this will be on the underside of the control panel.

Button for pushing assistance

5.1.1 On/Off button

Press the “Power” button to switch the control panel on
and off.

After it has been switched on, the system is always in the
medium power-assist mode

SPORT

.

The following applies only to bikes which are equipped
with a back-pedal brake:

The system will now perform a system check. At this time,
the LED on the left will now come on for approx. two sec-
onds, followed by all LEDs for approx. one second. If you
set off now, the system will normally detect a pedal move-
ment in the “drive” and “back-pedal brake” directions.
This completes the system check, and you can ride as
normal with assistance.

If you cannot feel any assistance, simply back-pedal
briefly and then pedal forwards again to trigger the
system check. In the event that the LEDs continue to
flash in the pattern described above and the motor is
not providing any assistance, then you should consult
a specialist dealer.

«
...
161
162
163
164
165
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: Qwic Pages: 120

Brand: Miche Pages: 24

Brand: CON-TEC Pages: 8

Brand: Ampler Pages: 18

Brand: Garmin Pages: 20

Brand: Hudora Pages: 15

Brand: Kidvelo Pages: 6

Brand: HNF-NICOLAI Pages: 124

Brand: VDO Cyclecomputing Pages: 3

Brand: Derby cycle Pages: 91

Brand: Vetta Pages: 14

Brand: Vetta Pages: 44

Brand: Kellys Pages: 88

Brand: Cateye Pages: 2

Brand: Christini Pages: 25

Brand: Babboe Pages: 4

E-HYBRIDE Andasol 4 Man / Lady

Brand: GHOST EPAC Pages: 180

RACE ATTACK RA-1

Brand: Rose electronics Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands