Kalkhoff Bosch Cruise User Manual Download Page 200 | Manualshive

Page: 200 / 550

background image

18

VI User Manual | Impulse Ergo Pedelec

Display

The display in the middle of the handlebar is divided into
five different display panels:

•

At the top on the left is your current

1

speed.

•

To the right of the current speed is a display show-
ing the selected

2

power-assist mode.

•

At the top on the right is the

3

battery symbol

which tells you the current charge status of your
Pedelec’s battery.

•

Below this, in the

4

remaining range indicator,

you can see the remaining distance over which you
will still receive assistance from the current bat-
tery charge.

•

Along the bottom section of the display is a long
information area that can be used to display the
following information:

•

How much of its potential output the motor is

currently delivering.

•

The costs that have been incurred in the course

of the current trip and during the Pedelec’s
entire service life.

•

The saving achieved in both euros and CO

2

in

comparison with the same journey by car.

•

The total number of kilometres covered by this

system.

•

Display of kilometres covered during the day

and overall.

•

Display of journey time during the current trip

and the top speed reached on this trip.

•

The average speed during the current trip and

the total distance covered.

1 Speed
2  Power-assist mode
3  Battery charge state
4  Remaining range indicator
5  Information area

1

4

5

2

3

5.1.1 Switching on/off

Press the power button to switch the Impulse system on.
After switching on, the system is always in the display
mode in which you switched it off.

If you cannot feel any assistance, simply back-pedal
briefly and then pedal forwards again to trigger the
system check. If there is still no assistance being
delivered, the instruction “Please move the pedals”
will continue to be displayed. In this case you should
consult a specialist dealer.

In order to switch your Pedelec off again, press the power
button on the control panel.

5.1.2 Pushing assistance

The pushing assistance moves the Pedelec slowly (at a
maximum speed of 6 km/h) without you having to turn the
pedals, e.g. if you are manoeuvring in a tight space or are
pushing your Pedelec out of a basement garage.

The pushing assistance is not suitable for use as start-
ing assistance.

«
...
198
199
200
201
202
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: Babboe Pages: 132

Brand: BAFANG Pages: 4

Brand: Puky Pages: 36

Luci Solar Bike Light Set

Brand: MPOWERD Pages: 5

Brand: IDEAL Bikes Pages: 100

Brand: Hamax Pages: 118

Brand: SP CONNECT Pages: 3

iPhone Bike Mount

Brand: NC-17 Pages: 66

Brand: Littium Pages: 24

Brand: Frisco Pages: 15

Brand: ENGWE-BIKES Pages: 20

Brand: Crivit Pages: 52

Brand: Cateye Pages: 2

Brand: BIKND Pages: 8

Brand: BikeBerry Pages: 44

Brand: Turner Pages: 12

Brand: Radio Flyer Pages: 6

CANNONDALE FG 9910

Brand: Ohlins Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands