Kalkhoff Bosch Cruise User Manual Download | Manualshive

Page: 141 / 550

background image

16

IV User Manual Pedelec with front motor

›

Check there is sufficient charge in the battery for
the journey you intend to make before setting off.

›

In winter the distance you can normally cover with
the battery operating normally is less. Only move
the battery from the warm room where you store
it and fit it on your Pedelec just before you set off.
This prevents low temperatures from reducing the
distance you can normally travel. A corresponding
diagram is provided in

Chapter 12 “Technical data”

.

›

The distance you cover can vary depending on the
topography, your handling, the condition of the
battery and the assist level you are using.

›

If all diodes flash consecutively, or several flash
at the same time (2 – 3 diodes), the battery is
damaged.

Before taking the battery to your specialist cycle shop
to have it checked, put the battery in the charger for
one minute then test it again.

6.5 Service life and warranty

6.5.1 the electric drive

The Panasonic front electric drive is a fully-developed
durable and maintenance-free electric drive. It is a wear
part for which a two-year warranty applies.

6.5.2 the battery

Batteries are wear parts. Wear parts also come with a two-
year warranty.

If the battery develops a fault during this period, your
specialist cycle shop will of course replace it. A fault does
not constitute normal ageing and battery wear.

The service life of the battery depends on different factors.
The most important wear-relevant factors are

•

the

number of charge cycles

and

•

the

age

of the battery.

When you have fully charged and discharged your battery
1,100 times, it will still have 60% of its initial capacity,
providing it has been well looked after:

BATTERY

REMAINING
CAPACITY

~ DISTANCE COVERED

8 Ah

4.8 Ah

19,360 km

12 Ah

7.2 Ah

30,800 km

18 Ah

10.8 Ah

52,800 km

From a technical standpoint therefore, the battery is
"used" at this point. It also goes without saying that the
battery ages. Even if you do not use your battery, its ca-
pacity reduces.

Providing you can still cover the journey distances with
this remaining battery capacity, you can of course con-
tinue using it. If the capacity is no longer sufficient, you
can take your battery to a specialist cycle shop who will
dispose of your battery and supply you with a new one.

›

You can extend the service life of the battery by
fully recharging it after every journey, even if it is
small. The Panasonic li-ion cobalt battery has no
memory effect.

›

You can also extend the service life of the battery
by using the assistance selectively. Avoid, for ex-
ample, using gears that make pedalling difficult
with the most powerful assist level.

«
...
139
140
141
142
143
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: Radio Flyer Pages: 6

Brand: NAKTO Pages: 30

Brand: Öhlins Pages: 8

Brand: Costway Pages: 6

Brand: HP Velotechnik Pages: 76

Brand: Babboe Pages: 91

Brand: Vanraam Pages: 55

Brand: Menabo Pages: 8

Brand: Argos Pages: 12

Brand: Yedoo Pages: 40

Brand: SALSA Pages: 2

Brand: Reynolds Pages: 14

Brand: Trikke Pages: 30

Brand: Viathon Pages: 32

Brand: KENT Pages: 60

Brand: Currier Tech Pages: 28

Brand: Wuxi LingDe Microelectronics Pages: 11

Brand: Canyon Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands