Kalkhoff Bosch Cruise User Manual Download Page 17 | Manualshive

Page: 17 / 550

background image

16

I General User Manual

9.2.4.3 With a suspension seatpost

Suspension seatposts reduce vibrations caused by uneven
roads thereby reducing stress on the spinal column.

If you need to adjust the suspension elements in the seat-
post, consult your specialist cycle shop.

Suspension seatpost

9.3 Adjusting the handlebar position

Tighten all screws to the prescribed torque as other-
wise screws could shear off and components could
come loose or detach altogether (see

➠

"Technical data"

).

You can also influence your riding position by changing
the handlebar height.

The lower you set the handlebar, the further you will have
to lean forwards. This increases the strain on your wrists,
arms and upper body and you will need to bend your back
further.

The higher the handlebar is, the more upright your riding
position will be. This increases the stress on your spinal
column due to jolting.

You can determine a handlebar height that best suits your
body size as follows:

›

Sit on the bike saddle.

›

Ask another person to hold the bike steady if
required.

›

Bend your upper body towards the handlebar until
you have found a position that is comfortable for
your back.

›

Stretch out your arms towards the handlebar.

›

Note the approximate position of your hands and
set the handlebar at this height.

9.3.1 Adjusting / aligning the handlebar

height with a conventional handlebar
stem

To release the stem shaft in the head tube, proceed as
follows:

›

Release the stem expander bolt to loosen the han-
dlebar stem. Turn it anticlockwise by two or three
revolutions using an Allen key.

›

Clamp the front wheel between your legs to pre-
vent the bike fork from turning with the stem shaft.

›

Holding the handlebar by the handles, turn it from
right to left and vice-versa.

›

If it is not possible to do this, tap lightly on the
stem expander bolt with a plastic hammer to loos-
en the clamping fixture inside the stem.

›

Set the handlebar stem to the required height.

›

Align the handlebar so that it is exactly at right
angles to the front wheel.

›

To secure the stem shaft again, turn the stem ex-
pander bolt clockwise using an Allen key until it is
tight (see

Chapter 30 "Technical data"

).

«
...
15
16
17
18
19
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

Brand: BAFANG Pages: 6

Brand: Manitou Pages: 12

Deluxe Big Flyer 474

Brand: Radio Flyer Pages: 2

Brand: Yuba Pages: 18

Brand: Tebco Pages: 10

Junior Pavement Cycle

Brand: Raleigh Pages: 2

Brand: VDO Cyclecomputing Pages: 56

Brand: Exposure Pages: 1

302655/20170601SZ187

Brand: APLIC Pages: 72

Brand: APLIC Pages: 80

Brand: FAFREES Pages: 84

Brand: DENAGO Pages: 16

Brand: Cateye Pages: 2

Brand: Cateye Pages: 36

Brand: BikeYoke Pages: 24

Brand: Yakima Pages: 30

Brand: QERIDOO Pages: 44

Shimano Steps E8000

Brand: Univega Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands