Kalkhoff Bosch Cruise User Manual Download | Manualshive

Page: 198 / 550

background image

16

VI User Manual | Impulse Ergo Pedelec

4.2 Learning cycle

After fully charging the battery for the first time and
thereafter roughly once every six months, you must
run the battery down until the system switches off.
This procedure (a so-called “learning cycle”) is nec-
essary so that the battery management recognises
the changes in the capacity caused by age and wear
and tear, in other words, the performance level of
the battery. Afterwards, the capacity of the battery is
calculated anew and correctly represented. This also
allows the remaining distance display to function with
greater precision. With this procedure, you can pre-
vent a sudden loss of electrical assistance during an
extended trip.

4.3 Charging operation

Before charging the battery, read the information on
the charger carefully.

1. Take the charger provided and the docking station out

of their packaging and plug the mains plug into a sock-
et (110-230 V, please observe the type plate on the
charger).

Type plates on charger and docking station

2. To charge the battery safely, the charger must be

placed on a dry, non-flammable surface resting on its
four feet and with the LED facing upwards. Do not cov-
er the charger. This is the only way to ensure that the

hot air around the battery warmed during the charging
operation can dissipate via the surrounding ventila-
tion slots.

3. Connect the plug of the charger to the docking station.

The LED in the charger now lights up briefly in red and
then permanently in green.

4. Put the battery in the charger. The battery and charger

are connected. The LED in the charger lights up in
green.

Battery in the docking station

5. The charging process begins. The LED of the charger

lights up in green. The battery LEDs light up one by
one to indicate the progress of the charging operation.
The battery is charged in five stages. When charging
of one stage is in progress, the corresponding LED
flashes. If this stage has been fully charged, the LED
will light up permanently. Now the next LED will begin
to flash. After all five LEDs have gone out, the battery
is fully charged.

6. If the LED on the charger flashes red permanently, a

charging fault has developed. In that case, disconnect
the battery from the charger, then connect it again.
The charger tests the battery and performs readjust-
ments, if required. If the LED on the charger still flash-
es, take the charger and battery to your specialist
dealer who will test the device and replace it, if
required.

7. To save power, pull the charger plug out of the socket

once the charging operation is complete.

Charging fault

«
...
196
197
198
199
200
...
»

Summary of Contents for Bosch Cruise







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Bosch Cruise

OYAMA 14380 Series

Brand: Clas Ohlson Pages: 72

Brand: smartmotion Pages: 17

Brand: TALARIA Pages: 31

Brand: Beta Pages: 61

TRANCE X ADVANCED SL 0

Brand: Giant Pages: 1

Brand: Miche Pages: 24

Brand: EG Pages: 10

Brand: Kayoba Pages: 49

Reach Trail(Offroad)

Brand: Pacific Pages: 11

Multi Bike Lifter

Brand: Garage Smart Pages: 16

Pedelec Groove*

Brand: Raleigh Pages: 397

Brand: Ice Bear Pages: 42

Brand: Rose electronics Pages: 2

Brand: Dedacciai Strada Pages: 20

Brand: Theraplay Pages: 8

SimpliAmp Thermal Cycler

Brand: Applied Biosystems Pages: 92

Brand: Veleon Pages: 98

Brand: topmove Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands