Indmar Raptor JET SERIES Operator'S Manual Download Page 45 | Manualshive

Page: 45 / 82

background image

7-1

© 2016 Indmar Marine Engines

Section Seven

MAINTENANCE

Before operating or maintaining the engine, review
“Safety” on page 1-1.

!

WARNING

• You can be injured if you try to work on your

marine engine without knowing enough about
your engine.

• Be sure you have the knowledge, experience

and the correct replacement parts BEFORE you
attempt any repairs.

• Be sure all fasteners you use are approved and

rated for marine use. Use of improper parts can
cause component or engine failure which may
result in death or serious personal injury.

GENERAL SERVICE NOTES

Your Indmar dealer is your best source for engine repair
and maintenance. Indmar certiﬁed technicians attend
ongoing service training programs and have the proper
diagnostic tools plus the latest speciﬁcations for your
engine.

!

DANGER

Electrical, ignition and fuel system components
on Indmar engines comply with U.S. Coast Guard
rules and regulations to minimize risks of ﬁre or
explosion. Use of replacement electrical, ignition
or fuel system components, which do not comply
to these rules and regulations, could result in a
ﬁre or explosion hazard and should not be used.

Your safety depends on your use of marine parts. When
servicing the electrical, ignition and fuel systems, it is
extremely important that all components are properly
installed and tightened. If not, any electrical or ignition
component could permit sparks to ignite fuel vapors from
fuel system leaks, if they existed.

Since marine engines may be expected to operate at
higher RPM ranges than typical automotive use for
most of their life, and to operate in fresh and salt water
environments, many special parts and fasteners are
used which are quite different from standard automotive
parts. Many parts are made from special corrosion
resistant materials while other moving parts are heavy-

«
...
43
44
45
46
47
...
»

Summary of Contents for Raptor JET SERIES



















































































Reviews:

No comments

Related manuals for Raptor JET SERIES

Brand: BAFANG Pages: 5

Brand: Quectel Pages: 71

Brand: Vascat Pages: 60

Brand: Continental Motors Pages: 146

Brand: Tanaka Pages: 10

Brand: Briggs & Stratton Pages: 20

Brand: O.S. engine Pages: 4

Throttling Governor Kerosene Stationary Engines

Brand: Worthington Pages: 33

Brand: YS Pages: 2

Brand: MULTIPLEX modell Pages: 11

Brand: Honda Pages: 5

Brand: Honda Pages: 16

Brand: Mitsubishi Heavy Industries Pages: 111

Brand: Paccar Pages: 92

Brand: Mitsubishi Pages: 68

Brand: Sachs Pages: 27

Brand: IAME Pages: 45

Brand: Nanni Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands