Indmar Raptor JET SERIES Operator'S Manual Download Page 66 | Manualshive

Page: 66 / 82

background image

8-6

SECTION EIGHT

EXTENDED STORAGE

If you must store your boat for an extended period
of time (more than normal off-season storage),
additional procedures are required. The procedures for
preparing for extended storage and recommissioning
after extended storage are best accomplished by an
authorized Indmar dealer.

Follow the normal procedures for off-season storage.

Recommissioning

1. Follow the normal procedures for recommissioning

after off-season storage.

2. Remove and clean the fuel injectors and ﬂush the

entire fuel system.

3. Install a new fuel ﬁlter.

4. Change all of the engine ﬂuids and lubricants. Install

a new oil ﬁlter.

5. Check all belts and hoses for cracks and wear.

Replace as needed.

6. Install new spark plugs. Check the wires for cracks

and damage.

7. Charge the battery and check battery connections to

make sure they are clean and tight.

8. Put fresh gasoline in the fuel tank that does not

contain ethanol. Cycle the key switch several times to
make sure the fuel system is full and primed. Install
an appropriate tester and verify the fuel pressure is
at speciﬁcation.

9. Apply water to the engine’s cooling system and start

the engine. While the engine is warming up, check
for leaks and smooth engine operation. Monitor the
fuel pressure to make sure it stays in speciﬁcation.

10. Put the boat in the water and operate it at various

RPM. Monitor the engine temperature, oil pressure,
charging voltage and fuel pressure to make sure all
stay within speciﬁcation. Check the various engine
operating parameters with a diagnostic scan tool to
make sure all parameters are within speciﬁcation.

«
...
64
65
66
67
68
...
»

Summary of Contents for Raptor JET SERIES



















































































Reviews:

No comments

Related manuals for Raptor JET SERIES

Brand: BAFANG Pages: 12

Brand: Regal Pages: 32

Brand: Chery Pages: 55

Reliance CDX7150

Brand: Baldor Pages: 32

Brand: CHERUBINI Pages: 24

Brand: TecumsehPower Pages: 24

Brand: Tecumseh Pages: 20

Brand: Tecumseh Pages: 8

Brand: Andersen Pages: 20

Brand: Chicago Electric Pages: 8

Brand: TCF Pages: 16

Brand: Briggs & Stratton Pages: 120

Brand: Seg Pages: 21

Brand: Toro Pages: 27

Brand: Volvo Penta Pages: 96

MotorLift RA20F

Brand: Chamberlain Pages: 24

Brand: Chamberlain Pages: 40

Brand: Louvolite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands