Indmar Raptor JET SERIES Operator'S Manual Download Page 57 | Manualshive

Page: 57 / 82

background image

7-13

MAINTENANCE

© 2016 Indmar Marine Engines

INDM-0017

Figure 7.7 – Fuse Box Layout

Fuses are located on top of the engine near the intake.
To remove or inspect a fuse, remove molded plastic
cap from fuse holder. Inspect fuse and replace if it is
defective. Make sure to replace the fuse block cover
when ﬁnished.

WIRING

If during maintenance or inspection, it becomes
necessary to move or reposition any of the engine’s
wiring or wire harnesses, verify that wiring is returned
to its original position, and that all harnesses are routed
correctly. If a wiring clip or retainer breaks, replace it
immediately. Wiring is speciﬁcally routed to eliminate
problems related to engine heat and spray, immersion
in liquids, or contact with rotating assemblies. Electrical
problems can result if wiring is moved from its original
position and is not properly repositioned.

Charging System Maintenance / Guidelines

Adhering to the following procedures and guidelines will
ensure proper operation of your battery charging system.
Watch out for:

1.

REVERSE BATTERY POLARITY:

When

reconnecting the battery after winter storage, it is
easy to accidentally reverse the battery leads and
connect positive to negative and negative to positive.
This generally results in a large arc at the battery
terminals and fail

ure of the diodes and/or regulator

in the alternator as well as other components in
the electrical system of the engine or boat that are

«
...
55
56
57
58
59
...
»

Summary of Contents for Raptor JET SERIES



















































































Reviews:

No comments

Related manuals for Raptor JET SERIES

VLT AutomationDrive FC 300 Series

Brand: Danfoss Pages: 56

Brand: Danfoss Pages: 2

Brand: VEM Pages: 35

Electric Motor G2909

Brand: Grizzly Pages: 2

Brand: Eaton Pages: 12

Brand: Atlas Copco Pages: 156

Brand: Stuart Turner Pages: 20

Brand: TCF Pages: 16

Brand: Robin America Pages: 36

Brand: Yanmar Pages: 76

Brand: Yanmar Pages: 234

BEVELMASTER 204B

Brand: TRI tool Pages: 46

Brand: Ingersoll-Rand Pages: 127

Brand: Wacker Neuson Pages: 108

Brand: Yanmar Pages: 240

Brand: Hirth Pages: 21

Brand: HandI Move Pages: 26

Brand: Garmin Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands