manualshive.com logo in svg

Indmar Raptor JET SERIES, Operator'S Manual, Page: 55 / 82

Share
Download
Indmar Raptor JET SERIES Operator'S Manual Download Page 55

7-11

MAINTENANCE

© 2016 Indmar Marine Engines

If the cooling system is completely empty, see your 
Indmar dealer for assistance immediately to purge 
system. Purging the system is a difficult procedure that 
is not recommended for the boat owner.

Salt and Hard Water Operation

All Indmar Marine engines are capable of operating in 
brackish or salt water as well as in hard water or water 
with high mineral content as long as certain precautions 
and maintenance procedures are followed. Your dealer 
will be aware if the local freshwater lakes in your area 
will require any special precautions to keep your engine 
functioning properly. Damage to the engine, both internal 
and external, that is a result of inadequate salt or hard 
water maintenance will not be covered under the Indmar 
Limited Warranty.

External Care

Your engine has been carefully primed and painted to 
protect it against rust and corrosion. To keep your engine 
looking like new, Indmar recommends applying an 
anti-corrosion compound. Regular application (every 3 
months) of this protectant, particularly on exposed metal 
surfaces, motor mounts and electrical connections, will 
displace water and seal the surfaces against penetration 

by corrosive agents. Rinsing the engine with fresh water 
between applications of the protectant will further protect 
the exposed surfaces.

INTERNAL (COOLING SYSTEM) CARE

Fresh Water Cooling – Half Systems

A fresh water cooling system that uses anti-freeze in the 
engine but raw water in the exhaust manifolds is referred 
to as a half-system. Although the engine is protected, 
it is still important to flush the engine with fresh water 
to remove as much salt water as possible from the 
raw water side of the cooling system as well as from 
the exhaust manifolds and risers. For more convenient 
flushing, ask your dealer about permanently installing a 
flushing device that allows easy connection of a water 
hose.

FRESH WATER COOLING

All fresh water cooling systems, must be inspected and 
maintained annually, usually during winterization.

Summary of Contents for Raptor JET SERIES



















































































Reviews:

No comments