Indmar Raptor JET SERIES Operator'S Manual Download Page 49

Page: 49 / 82

7-5

MAINTENANCE

Check the oil level with the dipstick at the start of the
day and then every time you get fuel. To get an accurate
reading, your engine should be warm and the boat
should be level.

ADD

OPERATING RANGE

SEE OWNERS MANUA

INDM-A003

Figure 7.2 – Dipstick

NOTICE

For best results wait about 5 minutes after you turn off
the engine to allow the oil to drain into the oil pan, giving
you a more accurate reading.

CAUTION! Engine and engine oil may be hot.

Pull

dipstick from engine.

2. Wipe oil off stick with clean towel/cloth.

3. Insert dipstick completely into the dipstick tube.

4. Remove dipstick and read oil level.

5. After reading is complete, return dipstick to tube.

6. Add oil if necessary.

Adding Oil

If oil level on the dipstick reads below the ADD mark,
add only enough oil to return level to FULL mark.

NOTICE

Do not overﬁll. If your oil level is above the full mark on
the dipstick, the engine may be damaged.

INDM-0018

1 -

Engine Oil Fill

Figure 7.3 – Engine Oil Fill

Summary of Contents for Raptor JET SERIES



















































































Search results

Summary of Contents for Raptor JET SERIES

Reviews:

Related manuals for Raptor JET SERIES

Brands by name

Popular brands

Indmar Raptor JET SERIES, Operator'S Manual

Search results

Summary of Contents for Raptor JET SERIES

Reviews:

Related manuals for Raptor JET SERIES

Brands by name

Popular brands