Indmar Raptor JET SERIES Operator'S Manual Download Page 13 | Manualshive

Page: 13 / 82

background image

xi

© 2016 Indmar Marine Engines

5. Positive Crankcase Ventilation (PCV) System

A. PCV

valve

B. Oil Filler Cap

6. Exhaust

System

A. Exhaust

manifold(s)

B. Exhaust

riser(s)

C. Exhaust valves
D. Catalytic

Converters

7. Miscellaneous Items Used on Above Systems

A. Hoses, clamps, ﬁttings, tubing, sealing gaskets or

devices and mounting hardware

B. Electronic

Controls

C. Electronic Control Module
D. Pulleys, belts and idlers

NOTICE

The repair or replacement of any warranted part
otherwise eligible for warranty coverage under the
Emission Control Warranty may be excluded from
such warranty coverage if Indmar demonstrates that
the engine has been abused, neglected, or improperly
maintained and that such abuse neglect or improper
maintenance was the direct cause of the need for repair
or replacement of the part.

The emission warranty covers damage to other engine
components that is caused by the failure of a warranted
part.

This manual contains written instructions for the proper
maintenance and use of your inboard engine. All
emission warranty parts are warranted by Indmar for the
entire warranty period of the engine.

Emission warranted parts that are scheduled for regular
inspection, but not regular replacement, are warranted
by Indmar for the entire warranty period of the inboard
engine.

Any emission warranty part repaired or replaced under
the terms of this warranty statement is warranted by
Indmar for the remainder of the warranty period of
the original part. All parts replaced under this limited
warranty become the property of Indmar.

If the ownership of a product is transferred during
Emission Components Warranty period, this warranty
shall also be transferred and be valid for the remaining
coverage period provided that Indmar is notiﬁed in the
following way:

a.

The former owner contacts Indmar and provides us with
the required information listed below; or

«
...
11
12
13
14
15
...
»

Summary of Contents for Raptor JET SERIES



















































































Reviews:

No comments

Related manuals for Raptor JET SERIES

Brand: Hacker Pages: 8

VLT AutomationDrive FC 300 Series

Brand: Danfoss Pages: 56

Brand: Danfoss Pages: 2

Brand: Man Pages: 64

Brand: Mile HaoXianG Model Technology Pages: 3

Brand: Black Bruin Pages: 70

Brand: Caple Pages: 16

Brand: Honda Pages: 86

Brand: Baumuller Pages: 24

Brand: Ingersoll-Rand Pages: 42

Brand: PACLITE Equipment Pages: 8

Brand: VACGEN Pages: 13

Brand: Ford Pages: 13

PERFORMANCE M-6007-X2302E

Brand: Ford Pages: 25

Brand: Ford Pages: 84

Brand: Marinediesel Pages: 248

Brand: Radne Pages: 20

Brand: 3W Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands