background image

M-6007-XEFMS 
340 HP Crate Engine 
GUIDE 

 

 

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF  

FORD RACING PERFORMANCE PARTS. 

 

 

Techline 1-800-367-3788

 

Page 1 of 13 

IS-1850-0290

 

Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356 

 
 
 

Please visit www.fordracingparts.com for the most current instruction information 

 

! ! ! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. 

AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD RACING 

TECHLINE AT 1-800-367-3788 ! ! ! 

 

FORD RACING PERFORMANCE PARTS PERFORMANCE ENGINE LIMITED WARRANTY 

 
Ford Racing Performance Parts warrants to the original retail purchaser for 12 months or 12,000 miles, 
whichever occurs first, that it will repair or replace, at its option, using new or remanufactured parts, Ford 
Racing Performance Parts engine covered part that, after inspection, is found to have failed due to a defect 
in factory supplied material or workmanship.  
 

Covered parts include the engine block and cylinder heads, all internally lubricated parts of the engine, including 
pistons, piston rings, piston pins, crankshaft and main bearings, connecting rods and rod bearings, camshaft and 
camshaft bearings, timing chain, timing chain gears, intake and exhaust valves, valve springs, oil pump, push rods, 
rocker arms, valve lash adjusters, hydraulic or mechanical lifters, and valve stem seals, to the extent that the 
original engine contains the referenced warranted part. Parts that require normal manufacturers recommended 
replacement intervals are not covered under this warranty.  
 
To the extent allowed by law, loss of time, inconvenience, loss of the use of the vehicle, commercial loss, and 
incidental and consequential damages are not covered. There is no other express or implied warranty on these 
Ford Racing Performance Parts Engines including, but not limited to, any implied warranty of merchantability or 
fitness for a particular purpose.  
 

This warranty does not cover: 

 

Parts which are replaced as part of normal maintenance. 

 

Installation or removal costs. 

 

Damage due to improper installation, negligence, alteration, or accident, including use related to racing or 
competition, marine or motorcycle applications, or for other non-vehicle usage. 

 

Engines where the vehicle odometer has been disconnected or the mileage has been altered. 

 

Damage caused by lack of proper maintenance, failure to follow maintenance schedule intervals, or failure 
to use or maintain proper type and levels of fluids, fuel, oil and lubricants. Proof of proper maintenance is 
the owner’s responsibility. Keep all receipts and be prepared to make them available if questions arise 
about maintenance. 

 

Towing, shipping, rental vehicles, loss of time, inconvenience, loss of use, or other economic loss. 

 

Ford Racing Performance Parts engines installed in vehicles registered and/or normally operated outside 
the United States and Canada.  

 
To obtain warranty repair or replacement, please contact Ford Racing Performance Parts at (800) 367-3788 or:  
 
Ford Racing Performance Parts  
P.O. Box 490  
Dearborn, MI 48121 

 
 
 
 
 
 
 
 
 

Summary of Contents for M-6007-XEFMS














Reviews: