manualshive.com logo in svg

Indmar Raptor JET SERIES, Operator'S Manual, Page: 52 / 82

Share
Download
Indmar Raptor JET SERIES Operator'S Manual Download Page 52

7-8

SECTION SEVEN

ENGINE FLAME ARRESTOR

Your engine is equipped with a U.S. Coast Guard 
approved flame arrestor. Its purpose is to contain any 
backfire that may occur during the operation of your 
engine. Because an inboard engine is completely 
enclosed, an uncontained backfire can be extremely 
dangerous.

INDM-0015

Figure 7.5 – Flame Arrestor

Periodically inspect flame arrestor to prevent clogging by 
dirt or corrosion. 

High-Performance Element-Type Flame 
Arrestor

Your engine is equipped with a high-performance 
USCG-approved element-type flame arrestor; special 
procedures are required. Consult your dealer for special 
servicing instructions for this flame arrestor.

!

 WARNING

Do not remove the flame arrestor at any time 
when the engine is being started or run as it may 
result in fire and explosion.

ENGINE COOLING

!

 WARNING

Running engine without adequate cooling can 
cause engine to overheat and may result in fire, 
explosion.

Summary of Contents for Raptor JET SERIES



















































































Reviews:

No comments