Indmar Raptor JET SERIES Operator'S Manual Download Page 31

Page: 31 / 82

3-3

PRE-START CHECKS

7. Your engine is equipped with a fresh water cooling

system. Check coolant level in the expansion tank.

8. Check alternator belt for wear and proper tension.

9. Verify that exhaust hoses are in good condition and

clamped tight.

10. Verify engine mounts are tight.

11. Check electrical connections and ensure connectors

are tight. Check wiring for signs of wear and
abrasion.

12. Verify throttle/shift control is functional and properly

adjusted.

13. Verify steering controls are functional and properly

adjusted.

14. Verify battery connections are clean and securely

fastened. Make sure the battery is fully charged.

15. Check the boat’s owner’s manual for additional pre-

operation checks.

INDM-A010

Figure 3.4 – Battery Connections

Summary of Contents for Raptor JET SERIES



















































































Search results

Summary of Contents for Raptor JET SERIES

Reviews:

Related manuals for Raptor JET SERIES

Brands by name

Popular brands

Indmar Raptor JET SERIES, Operator'S Manual

Search results

Summary of Contents for Raptor JET SERIES

Reviews:

Related manuals for Raptor JET SERIES

Brands by name

Popular brands