Indmar Raptor JET SERIES Operator'S Manual Download Page 65 | Manualshive

Page: 65 / 82

background image

8-5

STORAGE AND WINTER LAY-UP

© 2016 Indmar Marine Engines

REACTIVATING ENGINE AFTER EXTENDED

STORAGE

NOTICE

Use caution when connecting the battery cables.
Improperly connecting the battery cables or using the
wrong battery type can damage electrical components.
These damages are not covered by your warranty.

1. Charge and reinstall the battery in the boat. Make

sure the terminals are clean and tight.

2. Inspect the accessory drive belt and make sure that

it is routed properly.

3. If the fuel tank was drained, ﬁll the tank with fresh

fuel that does not contain ethanol.

4. Check all ﬂuid, oil, and coolant levels on the engine

and drive train.

5. Check the engine compartment and bilge for nesting

animals. Clean as necessary. Check for any damage
or evidence of ﬂuid leaks.

OTE:

N

With the boat in the water or a hose and adapter
installed, cycle the key switch ON, then OFF, for
ﬁve second intervals 3-4 times before cranking
the engine to allow the fuel pump to prime the
fuel lines.

6. Review boat manufacturer’s starting procedure.

7. Start the engine. If you experience a no-start

condition, do not crank the engine for more than 15
seconds without allowing a two minute cool-down
period. When the engine starts, keep a close watch
on the gauge readings. Check all of the hoses and
drain plugs for leaks. Listen for abnormal noises. Run
the engine long enough to reach normal operating
temperature and reinspect for leaks. If no leaks are
found, the boat is ready for operation.

«
...
63
64
65
66
67
...
»

Summary of Contents for Raptor JET SERIES



















































































Reviews:

No comments

Related manuals for Raptor JET SERIES

Brand: Wartsila Pages: 168

TSA 200-100-220

Brand: SCHABMULLER Pages: 56

Brand: Jiecang Pages: 2

Brand: Champion Power Equipment Pages: 29

Brand: York Pages: 40

Brand: Yanmar Pages: 52

WEST EUROTECH 36 T2

Brand: Weston UK Pages: 3

Brand: A'OK Pages: 7

Brand: Yamaha Pages: 51

Brand: Briggs & Stratton Pages: 200

Brand: Dato Pages: 9

Brand: DJ ENGINE Pages: 9

Brand: Lycoming Pages: 155

Brand: YS Pages: 2

Brand: Robin America Pages: 24

Brand: Jabiru Pages: 56

Brand: LRP electronic Pages: 11

Brand: ePropulsion Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands