manualshive.com logo in svg

IDEC FS1A-C11S, User Manual

Share
Download
IDEC FS1A-C11S User Manual Download Page 4

 

 

 

 

Warning 

 

 

Calculate respective safety distances, taking into consideration the response time of the 

SafetyOne, safety devices to be connected to the SafetyOne, and each other device that forms a 

part of the system configuration. 

 

Applicable safety performance is dependent on each system configuration. 

 

Use a power supply that meets following required specifications: 

-Conforms to the power supply rating of SafetyOne. 

-Complies with the SELV/ PELV circuit specified by EN 50178 or EN60950. 

-Has the functionality or the functional equivalent of the control voltage and current of class 2 

circuit, as defined in UL508 or UL1310. 

-Is in compliance with safety laws and regulations relating to electrical safety, EMC, and like under 

the laws and regulations of the country in which it is being used. 

 

Ground the V- line (0V DC) for ground diagnosis.   

 

In the case of a new configuration or modified installation, be sure to perform a check for each 

input and output function. 

 

Implement protective measures that personal, other than safety responsible persons operating 

the SafetyOne, are unable to modify the configuration. 

 

Separate SafetyOne from devices and wires which are not in accordance with class 2 circuit 

requirements. 

 

 

Summary of Contents for FS1A-C11S















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands