IDEC FS1A-C11S User Manual Download Page 36

Page: 36 / 398

INSTALLATION AND WIRING

3-6

Wiring method

SafetyOne has two kinds of connectors spring clamp (optional) and crimp.

Note1

Note1. For detailed information of Crimp connector, consult Tyco Electronics AMP.

■ Applicable connectors and mounting to SafetyOne

Applicable connectors

Type

No. of pole

Part No.

Remarks

Spring clamp

FS9Z-CN01

IDEC (optional)

2-1871940-5

Tyco Electronics Japan

FS9Z-CN02

IDEC (optional)

2-1871940-1

Tyco Electronics Japan

Crimp

2-1871946-5

Tyco Electronics Japan

2-1871946-1

Tyco Electronics Japan

Fig. 3.6 Spring clamp connector (FS9Z-CN0*) Fig. 3.7 Crimp connector

When mounting a connector to the SafetyOne, be sure to insert the connector straight and

completely in until you hear a click or feel it click into position. To remove the connector, press

down on the locking tabs completely, and then pull out the connector. If pressing down on the

locking tabs is incomplete damage to the connector and wire may occur.

■ Applicable wire and ferrule sizes for spring clamp connector

AWG#18-24 (UL1007 recommended) Stripped length: 7.0±0.3mm

When using ferrules, specification are shown below.

Long size: 1.02mm (min.) -

1.21mm (max.) (”a” in the figure below)

Short size: 0.95mm (min.) -

1.21mm (max.) (”b” in the figure below)

Applicable wire: AWG#24 (UL1007 recommended)

Fig3.8 Applicable Ferrule

Locking tabs

Tool insertion slot

Wire insertion slot

Wire

Terminal

Ferrule

Summary of Contents for FS1A-C11S














































































































































































































































































































































































































Search results

Summary of Contents for FS1A-C11S

Reviews:

Brands by name

Popular brands

IDEC FS1A-C11S, User Manual

Search results

Summary of Contents for FS1A-C11S

Reviews:

Brands by name

Popular brands