IDEC FS1A-C11S User Manual Download Page 151

Page: 151 / 398

LOGIC

5-103

r 5

When not using the start switch

（

Auto start

）

When not detecting the welding of start switch

（

Manual start

）

When detecting the welding of start switch

（

Control start

）

When connecting multiple emergency stop switches
in series

NOTE:

afety performance depends

on the system configuration.

When not using some safety inputs

・

In case of use only one of S1 or S2,

  open the unused safety input.
  This is same for safety S3 and S4.
  (Refer to (1))

・In case of unuse both of S1 and S2,
connect the recieve terminals to
orresponding dirive terminals. This is

same for S3 and S4. (Refer to (2))

・

If there are unused safety inputs in

  S5 and S6, connect the unused the
  receive terminals to the orresponding
  drive terminals. (Refer to (2))

24V DC

X10

X11

T10

T11

X12

T12

X13

T13

n+1

m+1

(1)

(2)

Summary of Contents for FS1A-C11S














































































































































































































































































































































































































Search results

Summary of Contents for FS1A-C11S

Reviews:

Brands by name

Popular brands

IDEC FS1A-C11S, User Manual

Search results

Summary of Contents for FS1A-C11S

Reviews:

Brands by name

Popular brands