manualshive.com logo in svg

IDEC FS1A-C11S, User Manual

Share
Download
IDEC FS1A-C11S User Manual Download Page 314

LOGIC 

5-266

 

 

●Safety input monitor outputs: Y4 to Y10 

Safety input monitor outputs are used to output the status of safety inputs in SafetyOne. 

Intended outputs 
(Terminal names) 

Target safety inputs 
(Terminal names) 

Description of operation 

Safety input 1 monitor output 
(Y4) 

Safety input 1 
(X0, X1) 

When the target safety input is ON, 
the monitor output is ON. When the 
target  safety  input  is  OFF,  the 
monitor output is OFF. 

Safety input 2 monitor output 
(Y5) 

Safety input 2 
(X2, X3) 

Safety input 3 monitor output 
(Y6) 

Safety input 3 
(X4, X5) 

Safety input 4 monitor output 
(Y7) 

Safety input 4 
(X6, X7) 

Safety input 5 monitor output 
(Y10) 

Safety input 5 
(X10, X11) 

Note. When the targeted safety input detects an input monitor error, input circuit failure, or EMC the 

disturbance, corresponding safety input monitor output becomes a pulse output (1Hz). The 
monitor output is OFF in other errors, Initial state, or Configuration state. 

 

●Safety output monitor outputs: Y12, Y13, Y17, and Y20 

Safety output monitor outputs are used to output status of safety outputs in SafetyOne.

 

Intended outputs 
(Terminal names) 

Target safety outputs 
(Terminal names) 

Description of operation 

Safety output 1 monitor output 
(Y12) 

Safety output 1 
(Y0) 

When the target safety output is ON, 
the monitor output is ON. When the 
target  safety  output  is  OFF,  this 
function is OFF. The monitor output 
turns 

OFF 

immediately, 

independent 

of 

the 

preset 

OFF-delay time. 

Safety output 2 monitor output 
(Y13) 

Safety output 2 
(Y1) 

Safety output 3 monitor output 
(Y17) 

Safety output 3 
(Y2) 

Safety output 4 monitor output 
(Y20) 

Safety output 4 
(Y3) 

Note. When the safety output detects an output circuit failure, the corresponding safety output 

monitor output becomes a pulse output (1Hz). The monitor output is OFF in other errors, 
Initial state, or Configuration state. 

Summary of Contents for FS1A-C11S















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands