IDEC FS1A-C11S User Manual Download Page 19

Page: 19 / 398

PRODUCT SPECIFICATIONS

2-7

r 2

Mean Time To dangerous Failure (MTTF

) and diagnostic coverage (DC)

・

In the case of using safety outputs as dual channel outputs

The following table describes MTTF

and DC in the case of dual channel outputs. They are

needed for the calculation of Performance Level (PL) which is applied to a system with

SafetyOne. In this case SafetyOne can be used in a system for PL a to e in accordance with EN

ISO13849-1.

Mean time to dangerous failure (MTTF

)

Diagnostic Coverage (DC)

100 years

High

・

In the case of using safety outputs as single channel outputs

The following table describes MTTF

and DC in the case of single channel outputs. They are

needed for the calculation of Performance Level (PL) which is applied to a system with

SafetyOne. In this case SafetyOne can be used in a system for PL a to d in accordance with EN

ISO13849-1.

Mean time to dangerous failure (MTTF

)

Diagnostic Coverage (DC)

100 years

Medium

Summary of Contents for FS1A-C11S














































































































































































































































































































































































































Search results

Summary of Contents for FS1A-C11S

Reviews:

Brands by name

Popular brands

IDEC FS1A-C11S, User Manual

Search results

Summary of Contents for FS1A-C11S

Reviews:

Brands by name

Popular brands