Hughes Direcway DW6000 Installation Manual Download

Page: 97 / 214

Chapter 4 • DW6000 LEDs and troubleshooting

1033295-0001 Revision A

•

LAN -

The LAN indicator shows whether the LAN is

connected and usable, and whether there is receive or
transmit activity.

•

Transmit -

The Transmit indicator shows whether the

DW6000 can transmit or is transmitting, or if some condition
is preventing transmission.

•

Receive -

The Receive indicator shows whether the DW6000

has acquired the correct outroute, is receiving, or if some
condition is preventing reception.

•

System -

The System indicator shows whether the DW6000

is operational or not. This indicator may also denote the
DW6002 is operational and VADB is enabled.

•

Power -

The Power indicator shows if the DW6000 is

powered on and operating normally.

Figure 65: DW6000 LEDs

IVE

27578 C
/16/05

HUGHES

LAN LED

stem LED

Power LED

Transmit LED

Receive LED

Summary of Contents for Direcway DW6000























































































































































































































Search results

Summary of Contents for Direcway DW6000

Reviews:

Related manuals for Direcway DW6000

Brands by name

Popular brands

Hughes Direcway DW6000, Installation Manual

Search results

Summary of Contents for Direcway DW6000

Reviews:

Related manuals for Direcway DW6000

Brands by name

Popular brands