Hughes Direcway DW6000 Installation Manual Download Page 167

Page: 167 / 214

Appendix C • Configuring the installer laptop for IP addressing

1033295-0001 Revision A

145

5. Select

Internet Protocol (TCP/IP)

. Be careful not to uncheck

the checkbox.

6. Select the

Properties

button. The

Internet Protocol Properties

window appears. See Figure 139.

7. Ensure that both

Obtain an IP Address Automatically

and

Obtain DNS Server Address Automatically

are selected. If

not, select them.

8. Select

to close the open dialog boxes and finish the

configuration.

9. Restart the computer even if Windows does not require you to

do so. This will ensure that the network settings are
automatically reset.

Figure 139: Internet Protocol Properties

Summary of Contents for Direcway DW6000























































































































































































































Search results

Summary of Contents for Direcway DW6000

Reviews:

Hughes Direcway DW6000, Installation Manual, Page: 167 / 214

Search results

Summary of Contents for Direcway DW6000

Reviews: