manualshive.com logo in svg

Hughes Direcway DW6000, Installation Manual, Page: 140 / 214

Share
Download
Hughes Direcway DW6000 Installation Manual Download Page 140

Appendix B • Installing the DW6000 using the Installer Console

 

118

1033295-0001  Revision A

AC/DC power supply

The power supply most commonly used is the AC/DC power 
supply shown in Figure 104. This power supply supports AC 
input power.

DC/DC power supply

The DC/DC power supply (Hughes part number 1033554-0001) 
shown in Figure 105 supports DC input power. The power supply 
is shipped in a kit (Hughes kit part number 1036088-0001) that 
also contains a DC input cable kit. The cable kit contains an input 
power connector, connector pins, and a wiring diagram; the kit 
does not contain wire.

Refer to the wiring diagram to assemble the DC input power 
cable.  

Figure 104:  AC/DC power supply

Note:

The installer must provide the wire required to assemble 

the DC input power cable.

Figure 105:  DC/DC power supply

Summary of Contents for Direcway DW6000























































































































































































































Reviews:

No comments