background image

 • About this document

 

xx

1033295-0001  Revision A

Appendix A – Installing the DW6000 using dial-up 
commissioning

 provides instructions on how to use the backup 

dial commissioning method.

Appendix B – Installing the DW6000 using the Installer Console

 

explains how to use the Installer Console to commission 
DW6000s for enterprise customers. Only use this installation 
method if instructed to do so by Hughes.

Appendix C – Configuring the installer laptop for IP addressing

 

provides information on configuring the laptop in various 
Microsoft operating systems.

Appendix D – Installing VADB

 provides instructions on how to 

install the optional Virtual Private Network Automatic Dial 
Backup (VADB) feature.

Appendix E – Using the Fallback Updater utility

 explains how to 

use the Fallback Updater utility to update the fallback.bin file on 
a DW6000.

Appendix F – Disabling the Web browser’s proxy connection

 

explains how to disable proxy server settings for Internet 
Explorer and Netscape.

Appendix G – Installation checklist

 provides an installation 

checklist.

Appendix H – Lat/Long Decimals to Minutes Table

 provides 

conversion information for installations where this data is entered 
manually.

There is also a safety summary, glossary, list of abbreviations and 
acronyms, and index.

Summary of Contents for Direcway DW6000























































































































































































































Reviews: