manualshive.com logo in svg

Hughes Direcway DW6000, Installation Manual

The Hughes Direcway DW6000 user manual is essential for getting the most out of your satellite internet experience. This comprehensive manual provides step-by-step instructions and troubleshooting guidance, ensuring seamless setup and optimal performance. Download the free manual from manualshive.com to enhance your satellite internet usage effortlessly.

Share
Download
background image

Appendix E • Using the Fallback Updater utility

 

1033295-0001  Revision A

159

Appendix E

Using the Fallback Updater utility

This appendix explains how to use the Fallback Updater utility to 
update the fallback.bin file on a DW6000 to the current software 
release. Only use the procedures in this appendix when instructed 
to do so by Hughes.

The utility must be saved on the installer laptop prior to updating 
the fallback.bin file and installing the DW6000. The utility is 
distributed to installers via e-mail and is also available for 
download on an installation support Web site. Installers will be 
notified by Hughes of the Web address for the site from where the 
utility can be downloaded.

Saving the utility on the 
installer laptop

Follow these steps to save the utility on the installer laptop:

1. Obtain the self-extracting file containing the utility and its 

supporting files.

2. Save the self-extracting file on the installer laptop.
3. Open the self-extracting file.
4. Select the location where the utility and its supporting files 

will be unzipped and saved. See Figure 148.

5. Click 

Unzip

. See Figure 148.

Note:

Make a note of the location where the utility and its 

supporting files are saved. You will need to locate them before 
using the utility.

Figure 148:  Saving the Fallback Updater utility on the installer 

laptop

Summary of Contents for Direcway DW6000























































































































































































































Reviews:

No comments

Related manuals for Direcway DW6000

RACOM RipEX Demo Handbook preview
RipEX
Brand: RACOM Pages: 56
Multitech MT5634MU User Manual preview
MT5634MU
Brand: Multitech Pages: 80
Paradyne HotWire 7914 User Manual preview
HotWire 7914
Brand: Paradyne Pages: 60
Maestro 100EVO SERIES Quick Start Manual & User Manual preview
100EVO SERIES
Brand: Maestro Pages: 32
KYL 668H User Manual preview
668H
Brand: KYL Pages: 6
Billion 5100SM Specifications preview
5100SM
Brand: Billion Pages: 1
RCA dcm235 User Manual preview
dcm235
Brand: RCA Pages: 112
AVM Fritz!Wlan Installation And Operation Manual preview
Fritz!Wlan
Brand: AVM Pages: 51
Toshiba V.9256K User Manual preview
V.9256K
Brand: Toshiba Pages: 120
USR IOT USR-G806 User Manual preview
USR-G806
Brand: USR IOT Pages: 47
RADEMACHER RolloHomeControl 8430-1 Brief Instructions For Commissioning preview
RolloHomeControl 8430-1
Brand: RADEMACHER Pages: 2
CalAmp TSLM User Manual preview
TSLM
Brand: CalAmp Pages: 62
CSL 20180724SZ237 User Manual preview
20180724SZ237
Brand: CSL Pages: 16
C-motech CDU-650 Technical Specifications preview
CDU-650
Brand: C-motech Pages: 19
Bausch Datacom DinBox RTU M4 Reference Manual preview
DinBox RTU M4
Brand: Bausch Datacom Pages: 50
Datum Systems PSM-4900L Application Manual preview
PSM-4900L
Brand: Datum Systems Pages: 14
UIS WFM-220 User Manual preview
WFM-220
Brand: UIS Pages: 4
Multitech MultiModem MT5634ZBA-V-V92 User Manual preview
MultiModem MT5634ZBA-V-V92
Brand: Multitech Pages: 101

Brands by name

Popular brands

Load more brands