manualshive.com logo in svg

Hughes Direcway DW6000, Installation Manual

The Hughes Direcway DW6000 user manual is essential for getting the most out of your satellite internet experience. This comprehensive manual provides step-by-step instructions and troubleshooting guidance, ensuring seamless setup and optimal performance. Download the free manual from manualshive.com to enhance your satellite internet usage effortlessly.

Share
Download
background image

Chapter 2 • Installing the DW6000 using satellite-based commissioning (SBC)

 

42

1033295-0001  Revision A

Connecting the DW6000 to 

the customer’s computer

Connect the customer’s computer to the DW6000 with an 
Ethernet cable. See Figure 42. Make sure the customer can 
browse to the Hughes Web site. If the customer cannot browse, 
see the instructions below.

If the customer cannot browse

Configure the installer laptop so its network properties match 
those of the customer’s PC. Refer to 

Appendix D

 for detailed 

instructions for setting network properties. Then:

1. Connect the installer laptop to the DW6000 with an Ethernet 

cable.

2. Open a Web browser on the installer laptop.
3. Enter the DW6000 IP address 192.168.0.1 in the browser 

URL location bar and press 

E

NTER

. If the DW6000 is 

functioning, the System Control Center appears.

4. Enter 192.168.0.1 in the browser URL location bar and press 

E

NTER

. If the site appears, the DW6000 is functioning. The 

customer should refer to the contact information on the 
System Control Center’s Help page to get technical support.

Figure 42:  Final configuration

Transmit cable
(Satellite Out)

AC power
cord

Ethernet
cable

Ethernet

Receive cable
(Satellite In)

Power
supply

DC power
cord

Summary of Contents for Direcway DW6000























































































































































































































Reviews:

No comments

Related manuals for Direcway DW6000

Chonghan CH-M2 User Manual preview
CH-M2
Brand: Chonghan Pages: 46
Go DGA0122 Quick Start Manual preview
DGA0122
Brand: Go Pages: 2
Cygnus 850 Quick Start Installation Manual preview
850
Brand: Cygnus Pages: 6
Ebyte NA611 User Manual preview
NA611
Brand: Ebyte Pages: 41
Raymar 2.4 MIU/PowerPort Series Installation & Operation Manual preview
2.4 MIU/PowerPort Series
Brand: Raymar Pages: 30
Paradyne COMSPHERE 3811Plus Installation Instructions Manual preview
COMSPHERE 3811Plus
Brand: Paradyne Pages: 13
Bausch Datacom DinBox PSTN Reference Manual preview
DinBox PSTN
Brand: Bausch Datacom Pages: 26
Radio Shack 25-3090 Owner'S Manual preview
25-3090
Brand: Radio Shack Pages: 8
Sitecom WLA-7100 Installation Manual preview
WLA-7100
Brand: Sitecom Pages: 12
Sitecom WL-522 Quick Installation Manual preview
WL-522
Brand: Sitecom Pages: 17
Hama 49061 Operating Instructions Manual preview
49061
Brand: Hama Pages: 28
Campbell CS-GSM/GPRS User Manual preview
CS-GSM/GPRS
Brand: Campbell Pages: 74
Black Box ME475A Specifications preview
ME475A
Brand: Black Box Pages: 2
Verizon AD3700 GLOBAL READY USB MODEM Product User Manual preview
AD3700 GLOBAL READY USB MODEM
Brand: Verizon Pages: 17
B&B Electronics Zlinx 485 Owner'S Manual preview
Zlinx 485
Brand: B&B Electronics Pages: 52
Campbell Airlink Raven Instruction Manual preview
Airlink Raven
Brand: Campbell Pages: 35
IBM PCI Data/Fax Modem User Manual preview
PCI Data/Fax Modem
Brand: IBM Pages: 46
Motorola SURFboard SB6141 Install Sheet preview
SURFboard SB6141
Brand: Motorola Pages: 2

Brands by name

Popular brands

Load more brands