manualshive.com logo in svg

Hughes Direcway DW6000, Installation Manual, Page: 145 / 214

Share
Download
Hughes Direcway DW6000 Installation Manual Download Page 145

Appendix B • Installing the DW6000 using the Installer Console

 

1033295-0001  Revision A

123

Powering up and 
reading the DW6000 
LED display

If the DW6000 for your installation uses an AC/DC power 
supply, and the power supply’s AC power cord is connected to a 
power strip or surge protector, connect the power strip or surge 
protector to a 110 V wall outlet or other AC power source.

The DW6000 LEDs will come on in the following order:

1. Power LED comes on solid to indicate the DW6000 is 

powered up.

2. LAN LED comes on within 30 seconds to indicate LAN 

connectivity is detected.

3. Power LED blinks, indicating the unit is not commissioned 

and therefore is running fallback.bin and not main.bin. 

Obtaining the IP address 

and testing the Ethernet 

connection 

1. Restart the installer PC so the DW6000 assigns it an IP 

address. Or type the command 

ipconfig /renew

 at a DOS 

command line prompt.

2. The embedded DHCP server assigns IP address 192.168.0.2 

to the installer PC. The DW6000 Address is set to 
192.168.0.1. Figure 111 shows a sample Windows TCP/IP 
Properties screen.

3. Type 

Ping 192.168.0.1

 at the DOS prompt and press 

E

NTER

. Figure 112 shows a successful ping attempt; 

Figure 113 shows an unsuccessful attempt.

 If the computer 

fails to ping the DW6000

, check that you installed the NIC 

properly and followed the instructions in Appendix C – 

Configuring the installer laptop for IP addressing,

 on 

page 141.

If the NIC is installed properly and TCP/IP is configured 
correctly, check that all the cable connections are secure. If 
they are, unplug the DW6000 from the power source; shut 
down and power off the computer; plug the DW6000 back in, 
and turn the computer back on. Then try the ping test again. If 
it is unsuccessful, call installer support for assistance.

Note:

In countries outside North America, the DW6000 may be 

plugged, with a physical adapter, directly into a 220 V outlet. 
Different countries may have different standards and requirements. 

Note:

Whenever the LEDs do not function properly as described 

in this section, make sure you have the correct power supply. Refer 
to page 117 for more information on power supplies.

Note:

The appearance of the TCP/IP Properties screen may 

vary among Windows operating systems.

Summary of Contents for Direcway DW6000























































































































































































































Reviews:

No comments