Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 76 / 138

Figure 3-26 Connecting power cables

Route a neutral wire from the middle of the positive and negative battery

strings.
The following figure uses a battery string consisting of 40 batteries as an

example. The battery neutral wire is routed from the middle of positive and

negative battery strings, each consisting of 20 batteries.

Figure 3-27 Neutral wire

●

One power source
If the mains input and bypass input share a power source, you do not need to

remove the copper bar between the mains and bypass input terminals or

connect the bypass input power cable.

Step 4 Route signal cables. Bind cables to the cabinet.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands