Huawei UPS5000-E-120kVA-FM User Manual Download | Manualshive

Page: 35 / 138

background image

Indicator

Color

Status

Description

Off

The bypass software is being upgraded.

Alarm

indicator

Yellow Steady

on

A minor alarm is generated for the bypass.

Off

There is no minor alarm for the bypass, or the

software is being upgraded.

Fault

indicator

Red

Steady

on

A critical alarm is generated for the bypass.

Off

There is no critical alarm for the bypass, or

the software is being upgraded.

Functions

The bypass module supplies power in the following cases:
The UPS is set to ECO mode and the bypass voltage is within the specified range.
The power module overload exceeds the time limit.
Both the active and standby ECMs are abnormal.
The system fails to run properly.
The power supply is switched to the bypass manually.

Specifications

●

Dimensions (H x W x D): 130 mm x 420 mm x 500 mm

●

Weight: 19 kg

●

Rated output capacity: 200 kVA

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

2 Overview

Issue 03 (2022-01-30)

Copyright © Huawei Technologies Co., Ltd.

27

«
...
33
34
35
36
37
...
»

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Reviews:

No comments

Related manuals for UPS5000-E-120kVA-FM

Brand: Homefibre Pages: 2

Brand: Abocom Pages: 3

Brand: SIYI Pages: 95

Brand: SMC Networks Pages: 2

Brand: Planet Pages: 2

Brand: ZyXEL Communications Pages: 263

Brand: Ubiquiti Pages: 24

Brand: TP-Link Pages: 2

Brand: Acer Pages: 63

Brand: Acer Pages: 38

Predator Connect X5 5G CPE

Brand: Acer Pages: 56

Brand: Acer Pages: 39

Brand: Acer Pages: 7

Brand: Sitecom Pages: 54

Brand: BandLuxe Pages: 80

Brand: Minitar Pages: 77

Brand: Fortinet Pages: 17

Brand: Fortinet Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands