Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 37 / 138

Figure 2-12 Signal panel on the control module

(1) Ground terminal

(2) Parallel port 1

(3) BSC port 1

(4) Ready switch on

ECM 1

(5) Indicators for ECM

(6) Parallel port 2

(7) BSC port 2

(8) Ready switch on

ECM 2

(9) Indicators for ECM

(10) Dry contact card (11) Dry contacts

(12) MDU port

(13) RS485 port

(14) Fast Ethernet (FE)

port

(15) COM2 port

(16) COM1 port

(17) Battery

temperature sensor

port

(18) Optional card

subrack cover

NO TE

Ports are protected by a security mechanism.

2.3.5.2 ECM

Appearance

The control module consists of two energy control modules (ECMs) in active/

standby mode.

Figure 2-13 ECM

Table 2-4 Ports on the ECM

Silk Screen

Description

PARALLEL

The PARALLEL port transmits parallel signals between racks.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

2 Overview

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands