Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 47 / 138

Table 2-11 Indicator status

Status

Color

Meaning

Red

A critical alarm has been generated, and the

buzzer sounds continuously.

Yellow

A minor alarm has been generated, and the

buzzer buzzes at 2 Hz.

Green

The UPS is running properly or a warning has

been generated.

Off

The MDU is powered off.

NO TE

The indicator on the MDU panel is yellow when the bypass supplies power in non-ECO

mode.

Figure 2-23 MDU ports

Table 2-12 Port description

No.

Port Name

Description

MUS05A

(DB26)

Connects to the MDU and monitoring interface card

Network port

CAN

Reserved

RS485_1

Reserved

FE_1

Reserved

FE_2

Reserved

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

2 Overview

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands