Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 54 / 138

shorten the battery lifespan and operating temperatures lower than 20°C

reduce the battery backup time.

3.1.1.3 Installation Clearances

Reserve the following clearances around the cabinet to facilitate operations and

ventilation:
●

Reserve at least 800 mm from the front of the cabinet to facilitate ventilation

and operations. Reserve at least 500 mm from the rear of the cabinet for

facilitate ventilation.

●

Reserve at least 500 mm from the top of the cabinet for operations.

Figure 3-2 Reserved clearances (unit: mm)

3.1.2 Tools and Instruments

CA UTION

Insulate installation tools to prevent electric shocks.

Prepare the following tools and meters indicated in

Table 3-1

for installation.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands