Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 68 / 138

3.3.2 Installing Batteries

D ANGER

● Before installing batteries, read through the battery safety precautions and

install batteries as instructed in the delivered battery installation guide.

● Install the batteries from the lower layer to the upper layer to ensure the

system is secure and balanced.

Install a battery rack and batteries. For details, see the battery installation guide

delivered along with the batteries.

3.3.3 Installing Optional Components

3.3.3.1 Installing Antiseismic Kits

Procedure

Step 1 Determine the installation positions for the antiseismic kits based on the delivered

marking-off template, and mark mounting holes.

Figure 3-15 Antiseismic kit mounting hole positions

Step 2 Secure two antiseismic kits to the front and rear of the cabinet using twelve

M5x16 screws and four M12 screws.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands