Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 85 / 138

Figure 3-38 Signal cable

NO TE

The number and colors of signal cables are for reference only.

Step 14 Install the right cover of the UPS cabinet on the right of the cable entry cabinet,

and install other covers in the original positions.

----End

3.3.6 Connecting a Remote EPO Switch

NO TICE

● The Company does not provide the EPO switch or cable. Prepare them by

yourself. The recommended cable size is 22 AWG.

● Equip the EPO switch with a protective cover to prevent misoperations, and

cover the cable with protective tubing.

● Triggering EPO will shut down the rectifier, inverter, charger, and static bypass,

but does not disconnect the UPS mains input. To power off the UPS completely,

open the front-end input switch when triggering EPO.

Connect the requisite EPO switch to UPS dry contacts.
●

Figure 3-39

shows the cable connections for an NC EPO switch.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands