Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 33 / 138

Indicator

Color

Status

Description

Blinking

at short

interval

The module is not configured, the inverter or

rectifier software is being upgraded, or the

inverter software is being upgraded (blinking

at 4 Hz, on for 0.125s and off for 0.125s).

Off

The rectifier software is being upgraded.

Alarm

indicator

Yellow Steady

A minor alarm is generated for the inverter or

rectifier.

Off

There is no minor alarm for the inverter or

rectifier, or the rectifier software is being

upgraded.

Fault

indicator

Red

Steady

A critical alarm is generated for the inverter or

rectifier.

Off

There is no critical alarm for the inverter or

rectifier, or the rectifier software is being

upgraded.

Functions

The power module consists of a power factor correction (PFC) rectifier and

inverter. It performs AC/DC or DC/DC conversion on the mains and battery inputs,

and stabilizes the bus voltage. The inverter (DC/AC) converts the inputs into sine

wave outputs.

Specifications

●

Dimensions (H x W x D): 86 mm x 442 mm x 620 mm

●

Weight: < 21 kg

●

Rated output capacity: 30 kVA/30 kW

●

Power density: 20.64 W/inch

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

2 Overview

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands