Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 78 / 138

Figure 3-29 Mounting holes for the cable entry cabinet (unit: mm)

NO TE

This section describes how to install the cable entry cabinet on the right side of the UPS. If

the cable entry cabinet needs to be installed on the left side of the UPS, remove the side

panel of the cable entry cabinet and the cable trough, and install them on the right side of

the cable entry cabinet.

Figure 3-30

shows the positions of the side panel of the cable

entry cabinet and the cable trough.

Step 2 Remove the right and rear covers from the UPS cabinet, and remove the front and

rear covers from the cable entry cabinet. Put away the removed screws and covers.

Step 3 Adjust the anchor bolts of the cable entry cabinet to make it flush with the UPS

cabinet.

Step 4 Install equipotential plate mounting kits on the same horizontal plane of the UPS

cabinet and cable entry cabinet.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands