Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 60 / 138

NO TE

● The input upstream circuit breakers recommended in

Table 3-4

are for reference only.

● If multiple loads are connected, specifications for branch circuit breakers must not

exceed the recommended specifications.

● The circuit breaker selection principle is to protect loads and cables, and the cascading

principle is to realize specific protection.

3.2 Transportation, Unpacking, and Checking

Context

NO TICE

● To prevent the UPS from falling over, secure it to a pallet truck using ropes

before moving it.

● To prevent shocks or falls, move the UPS gently. After placing the UPS in the

installation position, unpack it and take care to prevent scratches. Keep the UPS

steady during unpacking.

● If the UPS installation environment is in poor condition and the UPS needs to

be stored for a long time after it is unpacked, take measures to prevent dust. It

is recommended that the UPS be wrapped with the original plastic packing.

Procedure

Step 1 Use a pallet truck to transport the UPS to the installation position.
Step 2 Check the UPS packing.
Step 3 Hold the sliding plate steady. Cut and remove the binding tapes. Put down the

sliding plate gently. See

Figure 3-3

Figure 3-3 Removing binding tapes

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands