Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 53 / 138

Figure 3-1 UPS dimensions (unit: mm)

(1) Front door

(2) Foot

(3) Caster

(4) Base

(5) Rear panel

(6) Base installation

hole

(7) Beam

(8) Side beam

3.1.1.2 Installation Environment

●

Do not install the UPS in an environment where the operating temperature

and relative humidity are beyond the ranges stipulated in the technical

specifications.

●

Install the UPS away from water sources, heat sources, and flammable or

explosive materials. Keep the UPS away from direct sunlight, dust, volatile

gases, corrosive materials, and air dense with salt particles.

●

Do not install the UPS in environments with conductive metal scraps in the

air.

●

The optimal operating temperatures for valve-regulated lead-acid batteries

(VRLA batteries) are 20–30°C. Operating temperatures higher than 30°C

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands