Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 86 / 138

●

Figure 3-40

shows the cable connections for an NO EPO switch.

Figure 3-39 Cable connection for an NC EPO switch

Figure 3-40 Cable connection for an NO EPO switch

NO TE

● When you use the NC status, remove the jumper between EPO_NC and EPO_12V first.

When you turn off the EPO switch, EPO is triggered.

● When you use the NO status, ensure that the jumper is connected between EPO_NC and

EPO_12V. When you turn on the EPO switch, EPO is triggered.

3.3.7 Connecting Communications Cables

Procedure

Step 1 Connect the external network management device to the RS485 port of the

monitoring interface card.

Step 2 Connect the network port on a PC to the FE port of the monitoring interface card.

----End

3.4 Installing a Parallel System

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands