Arris RUCKUS R510, Quick Setup Manual

Page: 1 / 4

R510 Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions on
how to set up your Ruckus Wireless R510 Dual Band 802.11ac
Multimedia Wi-Fi Access Point. After completing the steps
described in this Guide, you will be able to place the Access Point
(AP) at your site and provide wireless network access to users.
NOTE: The R510 requires a minimum of ZoneDirector version
9.13 or later, or SmartZone firmware version 3.4 or later.
This Guide in Other Languages
• 请从以下网站获得该指南的简体中文版 https://
support.ruckuswireless.com .
• Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com .
• このガイドの日本語版は https://support.ruckuswireless.com で
ご覧ください。
• 이 가이드의 한국어 버전은 웹 사이트 ( https://
support.ruckuswireless.com ) 에서 확인하시기 바랍니다 .
• Veja a versão em português (Brasil) deste guia em https://
support.ruckuswireless.com.
• Puede ver la versión en español (América Latina) de esta guía
en https://support.ruckuswireless.com.
Before You Begin
Before deploying Ruckus products, please check for the latest
software and the release documentation.
• Release Notes and other user documentation are available at
http://support.ruckuswireless.com/documents .
• Software upgrades are available at http://
support.ruckuswireless.com/software .
• Software license and limited warranty information are
available at http://support.ruckuswireless.com/warranty .
Package Contents
A complete R510 installation package includes all of the items
listed below:
• R510 Access Point
• One wall-mount anchor kit, including two 1" No. 8 steel
panhead Phillips sheet metal screws, one 5mm M2.5 x 1.06
Torx security screw, and wall-mount anchors
• One external T-bar bracket (two unassembled parts)
• One unit removal pin
• Regulatory flyer
• Product warranty statement
• Declaration of Conformity, if required
• This Quick Setup Guide
Step 1: Collecting Setup Requirements,
Hardware and Tools
• A computer running Windows 7 (procedures for other OS’s are
similar)
• Two Cat 5e Ethernet cables
• No. 2 Phillips screwdriver and T8 Torx driver for wall mounting
anchor kit
• An AC power adapter (sold separately), or
• an 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector
• When mounting the R510 to a truss or pole, two customer-
supplied cable ties
IMPORTANT-QSG: If the AP is deployed with a ZoneDirector,
then refer to the ZoneDirector Quick Setup Guide and connect
the AP to your local network.
Step 2: Connecting Your Computer to the
AP
FIGURE 1 Top view
1. After removing your Ruckus AP from its package, place it
next to your computer.
2. Using an Ethernet cable, connect your computer’s network
port to one of the two ports on the AP.
3. Using an AC adapter (sold separately), connect the AP 12VDC
port to a protected power source.
Alternatively, connect the PoE port to a PoE injector or switch
for both power and network connections
4. Verify that the Power LED on the external enclosure is slowly
flashing green.
FIGURE 2 Bottom view
Step 3: Preparing Your Computer for AP
Setup
NOTE: The following procedures assume Windows as the
operating system. Procedures for other operating systems are
similar.
1. On your Windows PC, configure your network adapter from
the Local Area Connection settings as follows:
Start > > Control Panel > Network and Sharing Center >
Change Adapter Settings
2. Edit the TCP/IPv4 address settings as follows:
Local Area Connection > Properties > Internet Protocol
Version 4 (TCP/IPv4) > Properties
The Internet Protocol Version 4 (TCP/IPv4) Properties dialog
box appears.
IMPORTANT-QSG: Write down all of the currently active
settings so you can restore your computer to its current
configuration later (when this process is complete).
3. Select Use the following IP address (if it is not already
selected) and then make the following entries:
• IP address: 192.168.0.22 (or any available address in the
192.168.0.x network, except 192.168.0.1)
• Subnet mask: 255.255.255.0
• Default gateway: 192.168.0.1
Leave the DNS server fields empty.
4. Click OK to save your changes. Your changes are put into
effect immediately.
Step 4: Logging Into the AP
1. As specified in Step 3, the admin PC should be directly
connected to the AP through one of the Ethernet ports and
powered on, ready for setup.
2. On your admin PC, open a web browser window.
3. In the browser, enter the following URL in the browser
navigation bar:
https://192.168.0.1
Copyright
©
2019 CommScope, Inc. All rights reserved. Page 1 of 4
Published November 2019, Part Number 800-70940-001 Rev G