HP ProLiant DL380e User Manual Download

Page: 73 / 155

RBSU menu (HP ProLiant G7 servers or server blades) 73

Custom POST Message (G7 servers)

The Custom POST Message option enables the user to enter a custom message to display during POST.

Advanced Options (G7 servers)

The Advanced Options menu includes the following options:

•

Advanced System ROM Options (G7 servers)

•

Video Options (G7 servers) (on page

)

•

Power Supply Requirements Override (HP ProLiant DL580 G7 Servers) (on page

)

•

Thermal Configuration (G7 servers) (on page

)

•

Service Options (G7 servers) (on page

)

•

Advanced Performance Tuning Options (G7 servers) (on page

)

•

Drive Write Cache (G7 servers) (on page

)

•

Asset Tag Protection (G7 servers) (on page

)

IMPORTANT:

Menu options may differ from those in this document, depending on specific

server options.

Summary of Contents for ProLiant DL380e




























































































































































Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands

HP ProLiant DL380e, User Manual

Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands