HP ProLiant DL380e User Manual Download

Page: 88 / 155

RBSU menu (HP ProLiant G7 servers or server blades) 88

Adjacent Sector Prefetch (G7 servers)

The Adjacent Sector Prefetch option allows processor prefetch features to be disabled. In most cases, the

option should remain enabled. The option should be disabled only after performing application
benchmarking to verify improved performance in a particular environment.

DCU Prefetcher (G7 servers)

DCU prefetcher allows the disabling of a processor prefetch feature. In very limited cases, setting this

option to

Disabled

may improve performance. In the vast majority of cases, the default value of

Enabled

provides better performance. Users should only disable this option after performing application

benchmarking to verify improved performance in their environment.

•

Enabled (Default)

Summary of Contents for ProLiant DL380e




























































































































































Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands

HP ProLiant DL380e, User Manual

Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands